新2手机会员端网址(中国)责任有限公司

新2手机会员端网址
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 行业新闻

自上料搅拌车筛网叶片出现故障需及时维修

所属分类:行业新闻 发布时间:2022-05-18 来源: 浏览量:0

由于筛网采用普通钢材,经常存在质量差、耐磨性差的问题,包角不够合理,因此在应用过程中容易损坏,出现大面积渗漏,甚至混音器也无法使用。
Because the screen is made of ordinary steel, there are often problems of poor quality and poor wear resistance, and the wrap angle is not reasonable enough. Therefore, it is easy to be damaged in the application process, large-area leakage occurs, and even the mixer can not be used.
另外,有些搅拌筛的目数不够科学,筛分率太低,导致已筛分的砂石粒度小。如果自上料搅拌车的筛网尺寸不够合理,钢材质量不达标,那么再先进的自上料搅拌车也无法搅拌出高质量的混凝土。
In addition, the mesh number of some mixing screens is not scientific enough, and the screening rate is too low, resulting in small particle size of screened sand and stone. If the screen size of the self loading mixer is not reasonable enough and the steel quality does not meet the standard, the most advanced self loading mixer can not mix high-quality concrete.
自上料搅拌车筛网故障维修中应使用耐磨钢丝,设置科学的钢丝直径和筛网目数,适当增加筛网的面积,提高筛分率,节约原料,从而提高生产效率。发现筛线断线后,立即拧紧筛网螺栓,重新设置筛网长度。
Wear resistant steel wire should be used in the maintenance of screen fault of self loading mixer truck, set scientific steel wire diameter and screen mesh, appropriately increase the screen area, improve the screening rate and save raw materials, so as to improve the production efficiency. When the screen wire is broken, immediately tighten the screen bolt and reset the screen length.
自上料搅拌车筛网叶片出现故障需及时维修
If the screen blade of the self loading mixer fails, it shall be repaired in time
此外,叶片故障也是一个重大故障。叶片作为自上料搅拌车设备的重要部件之一,对搅拌过程有着直接的影响,叶片的好坏在一定程度上可以决定自上料搅拌车的使用寿命。因此,在自上料搅拌车使用过程中,叶片的损坏程度往往比较高,因此需要注意叶片技术。
In addition, blade failure is also a major failure. As one of the important components of the self loading mixer, the blade has a direct impact on the mixing process. The quality of the blade can determine the service life of the self loading mixer to a certain extent. Therefore, in the process of using the self loading mixer, the damage degree of the blade is often high, so we need to pay attention to the blade technology.
自上料搅拌车每次搅拌完毕后,需要立即清洗自上料搅拌车的叶片,以便及时清理叶片上的污垢。自上料搅拌车的叶片和振动轴承应滴上润滑油,自上料搅拌车的叶片应防锈除锈。
After each mixing of the self loading mixer truck, the blades of the self loading mixer truck need to be cleaned immediately in order to clean the dirt on the blades in time. The blades and vibration bearings of the self loading mixer shall be dripping with lubricating oil, and the blades of the self loading mixer shall be rust proof and derusted.
自上料搅拌车厂家认为,定期检查自上料搅拌车的叶片手柄和叶片焊接质量,检查叶片磨损和消耗情况。一旦发现异常问题,应及时记录并更换,并检查刀片底部导通状态,避免刀片损坏。泄漏发生在焊点处。
The manufacturer of self loading mixer truck believes that the welding quality of blade handle and blade of self loading mixer truck shall be inspected regularly, and the blade wear and consumption shall be inspected. Once any abnormal problem is found, it shall be recorded and replaced in time, and the conduction state at the bottom of the blade shall be checked to avoid blade damage. Leakage occurs at the solder joint.
本文的精彩内容由自动上料搅拌车提供知识提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:/我们有专门的客服为您解答问题
The wonderful content of this article is provided by the knowledge of automatic feeding mixer. There are many wonderful contents on this website. You can click to enter more contents: / We have special customer service to answer your questions

 

首页 产品 电话 置顶
Baidu
sogou